
A substation earthing grid is the one part of a substation you cannot inspect, repair or improve after the concrete is poured. Every decision that matters is taken in the two weeks before the excavation is backfilled, and most of them are taken by people who will never see the finished installation.
What the Earthing Grid Actually Has to Do
The grid does three jobs at once. It carries fault current away from the faulted equipment without overheating. It holds the potential of the soil under the operator’s feet close to the potential of the equipment they are touching, so that step and touch voltages stay inside the safe curve. And it gives the surge protection a low-impedance path to earth, so a lightning impulse does not travel back through the control cabinet.
A grid that satisfies only the first job is the common failure. It measures a low resistance on a Megger at handover, passes the test sheet, and still kills someone during a fault because the mesh was too coarse near the operating position.
6 Checks Before You Pour Concrete
- Measure soil resistivity before you design, not after. Take Wenner four-pin readings at several spacings along the grid diagonals, down to the depth the grid will actually reach. A single reading at one spacing tells you almost nothing about a layered soil.
- Set the mesh spacing from the fault current. Mesh size drives step and touch voltage far more than conductor size. Tighten the mesh near walkways, operating handles and cable trenches; a uniform grid across the whole yard is usually over-designed in the corners and under-designed where people stand.
- Size conductors for the fault duty, not the steady load. Use the prospective fault current and its clearing time, apply the material’s fusing constant, and add corrosion allowance. A copper conductor sized for 1 s at 25 kA is not the same conductor you need for 3 s.
- Detail the joints as if they will be buried for thirty years. Exothermic welds or brazed joints, never a plain compression lug in the soil. Every joint below grade is a future resistance point; every joint above grade is one you can still inspect.
- Check step and touch voltage by calculation, then by measurement. Run the mesh calculation with the actual fault current and the actual surface layer, then verify the resistance and continuity after installation. Gravel or asphalt surfacing is part of the design, not a finishing choice.
- Keep the grid bonded to everything that can be touched. Switchgear frames, cable boxes, transformer tanks, steel structures, fence posts and the cable screens all connect to the same grid. A floating metallic part inside the yard is the most dangerous object on site.
The interface with the building slab matters as much as the grid itself; the cable entry, plinth and drainage detail in our outdoor RMU foundation steps shows where the earthing conductor has to be left accessible before the panel lands.
Soil Resistivity and Mesh Design Compared
Four parameters decide whether the grid works. The table below shows what each one controls and the consequence of getting it wrong.
| Parameter | Typical range | What it controls | If it is wrong |
|---|---|---|---|
| Soil resistivity | 50 – 3,000 Ω·m | Overall grid resistance and mesh voltage | Grid too large, or too small by a factor of two |
| Mesh spacing | 3 – 10 m | Step and touch voltage near walkways | Dangerous touch voltage at the operating handle |
| Conductor size | 70 – 185 mm² copper | Fault current withstand and corrosion life | Conductor fuses or corrodes open in service |
| Surface layer | 50 – 150 mm gravel | Body current through the feet | Touch voltage exceeds the safe curve |
On rocky or high-resistivity sites, the answer is rarely a bigger grid. Bentonite backfill around the conductors, deep driven rods at the corners, or a treated earth pit will do more per unit cost than adding another ring of conductor. In coastal yards, the corrosion detail in our coastal corrosion notes applies to buried copper just as it does to painted steel.
Materials and Joints That Survive 30 Years
- Annealed copper conductor, or copper-bonded steel where the budget rules out solid copper.
- Exothermic welded joints below grade; brazed or clamped joints above grade with inspection access.
- Bentonite or a purpose-made ground enhancement material around conductors in high-resistivity soil.
- Gravel surfacing at least 100 mm deep over the operating areas, kept free of soil and vegetation.
- Test pits at the corners, with the conductor tails left long enough to clamp a meter onto.
- As-built drawings that record the actual conductor positions, not the design positions.
Once the yard is live, the earthing system joins the routine inspection cycle; the checks that belong there are listed in the MV switchgear inspection and testing plan. Where the site sits in a seismic zone, the conductor routing also has to survive ground movement, and the switchgear seismic design notes cover the anchorage side of that problem.
FAQ
How often should the earthing resistance be measured?
At handover, then annually for the first three years, then every three to five years unless the soil is aggressive or the readings drift. Record the test point, the meter used and the weather.
Is a low resistance reading enough to prove the grid is safe?
No. Resistance proves the grid conducts; it says nothing about step and touch voltage. The mesh calculation and the surface layer decide whether a person survives a fault at the operating position.
Can the grid be extended after commissioning?
Only above the surface layer. Adding buried conductor later means excavation in a live yard, which is usually scheduled as an outage. Design the mesh for the final fault level, not the first one.
What fails first in a buried grid?
Joints, and then conductor sections under leaking drainage or cable trenches. Water and stray current do more damage than soil resistivity ever does.
Do I need a separate earth for the control and protection system?
No separate electrode that can float. Bond the control earth to the main grid at one defined point, and keep signal cables screened and routed so the fault current does not travel through the control cabinet.
About Electric-GS
Electric-GS is an OEM/ODM switchgear factory in Yueqing, Zhejiang, China. We build ring main units, GIS, MV and LV switchgear, cable boxes and packaged substations, and we supply the earthing, cable entry and foundation details that switchgear installation teams need before civil work starts. Send your single-line diagram and fault level to info@electric-gs.com or WhatsApp +86 135 8897 8050. English product pages are on electricgs.com, and Chinese technical notes on electric-cn.com.


One thought